Where to get a "power pipe"?

Rick 91GT · 09-17-2001, 06:50 PM

Well I mocked up a PP this last week relocating the 76mm C&L to the bottom, it didn't like that so I changed the design to keep it up towards the stock location. I used PVC to mock it up and I am just going to buy some mandrel bent tubing. I have found the tubing from any Diesel Truck shop, and a buddy of mine bought some from JC Whitney, I have a link to the Diesel Shop, I'll post it tomorrow from work. If I can make it there is no way I am going to spend $190 on one from AFM.

I heard on another board you can buy the C&L tube like the one that comes on the 76mm for $40 but I do not know for sure. Tiny advenger also sells one, they advertise in the back on the MM&FF and 5.0 I think.

------------------
Check Out My Site 91GT,Holley SysteMAX II Kit-Heads 2.02" x 1.60" port matched to a 1262,Anderson N-61,24#,76mm C&L,Full MAC, No A/C or PS or emissions, 12" K&N Filter,RNH PERFORMANCE Ram Air,Ron Davis Radiator,Full Suspension, SPEC stage III clutch, Lakewood SFI bell, S&W 8pt "X" brace,JAZ seats,3:73's,Welds..etc,4:30's and 31 splines coming very soon!
[b]12.16 @ 113.5, 1.78 60ft..no traction in the 90 degree

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Power Pipe installation question	p51302	Power Adders	2	06-02-2004 05:13 PM
offroad H or X pipe??	03stangGT	Modular Madness	4	10-23-2003 04:49 PM
Off road pipe vs. Catalitic Pipe	Kamaro Killer	Windsor Power	7	04-04-2002 04:05 AM
Need Power What Should I Do Next? Thanks	ewalker302	Windsor Power	12	04-01-2002 10:27 PM
Power Pipe on a Procharger?	NO SLO PK	Windsor Power	0	01-25-2001 07:14 PM

09-17-2001, 06:50 PM	#2
Rick 91GT Procharged! Join Date: May 1999 Location: Hanover, PA Posts: 1,539	Well I mocked up a PP this last week relocating the 76mm C&L to the bottom, it didn't like that so I changed the design to keep it up towards the stock location. I used PVC to mock it up and I am just going to buy some mandrel bent tubing. I have found the tubing from any Diesel Truck shop, and a buddy of mine bought some from JC Whitney, I have a link to the Diesel Shop, I'll post it tomorrow from work. If I can make it there is no way I am going to spend $190 on one from AFM. I heard on another board you can buy the C&L tube like the one that comes on the 76mm for $40 but I do not know for sure. Tiny advenger also sells one, they advertise in the back on the MM&FF and 5.0 I think. ------------------ Check Out My Site 91GT,Holley SysteMAX II Kit-Heads 2.02" x 1.60" port matched to a 1262,Anderson N-61,24#,76mm C&L,Full MAC, No A/C or PS or emissions, 12" K&N Filter,RNH PERFORMANCE Ram Air,Ron Davis Radiator,Full Suspension, SPEC stage III clutch, Lakewood SFI bell, S&W 8pt "X" brace,JAZ seats,3:73's,Welds..etc,4:30's and 31 splines coming very soon! [b]12.16 @ 113.5, 1.78 60ft..no traction in the 90 degree