IFS drop spindles on 65-66?

[bmxmon]

I dont think that will work, the tie rod mount is towards the front in the mustang II.
----------------------------------------------

I just noticed this thread is from 2001, whats up!!?

[dav65mus]

Originally Posted by bmxmon

I dont think that will work, the tie rod mount is towards the front in the mustang II.
----------------------------------------------

I just noticed this thread is from 2001, whats up!!?

Maybe he has been trying to get them to fit for 6 years

[66-351]

Originally Posted by dav65mus

Maybe he has been trying to get them to fit for 6 years

I just joined and didn't notice the date.

[66-351]

[QUOTE=bmxmon;329382]I dont think that will work, the tie rod mount is towards the front in the mustang II.
----------------------------------------------

What if you swapped sides with them? (left to right and right to left) If it won't work, no biggie. I have heard of the swap for the early stangs. Just wondered if it was B--- Sh-- or not. Thanks.

[dav65mus]

Sorry, my post was meant as a lame attempt at a laugh. However if you are attempting to switch spindles from side to side, that won't work because of the tie rod arm pointing in the wrong direction. Good luck, Dave


P.S.....about 25 years ago I swapped a linclon versailles disc brake rearend into my 66 stang........me and my buddy spent 4 months and about 3 gallons of brake fluid and 6 different master cylinder combos to get the correct pedal height and feel.......thus my lame attempt for a laugh.

This post being so old reminded me of that and I laughed at the thought that this car had been on jackstands for 6 years and they were still trying to figure out how to make those spindles fit! (obviously it could'nt have been but I am easily ammused)

[66-351]

This post being so old reminded me of that and I laughed at the thought that this car had been on jackstands for 6 years and they were still trying to figure out how to make those spindles fit! (obviously it could'nt have been but I am easily ammused)[/QUOTE]

Hey, you never know. hahaha

[66-351]

[QUOTE=dav65mus;329422]Sorry, my post was meant as a lame attempt at a laugh. However if you are attempting to switch spindles from side to side, that won't work because of the tie rod arm pointing in the wrong direction. Good luck, Dave


If the tie rod mount is to the front on the Mustang II and to the rear on the early Mustang, then swapping sides WILL put them pointing in the right direction. If you take a tie rod mount that is to the rear on the left side and put it on the right side it will put the tie rod mount in the front.

[bmxmon]

Thats in interesting thought, might as well give it a try. Hey Dav65mus, how'd the versailles swap go, do you think its a better idea to swap in the different rear end or just get a kit from somebody like ssbc?

[dav65mus]

get a kit from ssbc.

I did that swap back in about 83or 84, and about a year after I swapped the versailles rearend in, the driver side caliper locked and I smelled something burning......... stopped the car and the rotor was smoking and glowing cherry red! Replacement parts were hard to get then only about 8 years after they were new.

You do get a proper width 9" rearend with the swap, but its not worth it today with ssbc,baer, and willwood options out there.

[dav65mus]

Also about the spindle swap,as someone posted earlier, the granada or monarch spindles from the mid 70's will bolt onto a 65-66 stang without bad problems.

Mustang 2 spindles will not fit properly as a direct bolt on...... and even if you got them on...... without a complete weld in mustang 2 frontend kit your steering geometry and bumpsteer would make the car dangerous to drive.