HELP WITH TORQUE BOXS AAAAAHHHHHH

Rick 91GT · 10-26-2001, 09:47 AM

Well I make a kit very similar to tht Wild Rides but mine have a extar plate that ties it to the frame on both sides and they are made from Stainless so they will not rust.

If you already have the Wild Rides kit in I would suggest, tap all the seams back together and make sure they are square again and FULLY WELD all thr factory seams and I welded the top plates to the floor board as well (The ones under the rear seat)

If your boxes are really trashed and non repairable South Side Machine makes a replacement adjustable torque box, but I have never delt with this so I do not know if it works.

I damaged my boxes very bad since I run the SSM which tend to be hard on the boxes, after welding the seams and adding the re-enforcement kit I have never had a single problem. I also welded plate across the bottom so it boxes the arm in a little. You just need to notch it out so that the arm still has room to travel. Wolfe sells similar plates for $25.00.

------------------
Check Out My Site 91GT,Holley SysteMAX II Kit-Heads 2.02" x 1.60" port matched to a 1262,Anderson N-61,30#,76mm C&L,75mm Accufab, Full MAC, No A/C or PS or emissions, 12" K&N Filter,RNH PERFORMANCE Ram Air,Ron Davis Radiator,Full Suspension, SPEC stage III clutch, Lakewood SFI bell, S&W 8pt "X" brace,JAZ seats,3:73's,Welds..etc,4:30's and 33 splines coming very soon!
[b]12.16 @ 113.5, 1.78

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
raced a Supra Twin Turbo	Stang35th	Stang Stories	63	08-23-2003 12:36 AM
Torque strap. Yes or no	Dark_5.0	Windsor Power	3	06-05-2003 07:00 AM
T-5 Torque Rating	sleeperstang	Classic Mustangs	5	07-05-2002 10:54 PM
T-5 Torque Rating	sleeperstang	Windsor Power	1	06-27-2002 08:18 PM

10-26-2001, 09:47 AM	#1
Rick 91GT Procharged! Join Date: May 1999 Location: Hanover, PA Posts: 1,539	Well I make a kit very similar to tht Wild Rides but mine have a extar plate that ties it to the frame on both sides and they are made from Stainless so they will not rust. If you already have the Wild Rides kit in I would suggest, tap all the seams back together and make sure they are square again and FULLY WELD all thr factory seams and I welded the top plates to the floor board as well (The ones under the rear seat) If your boxes are really trashed and non repairable South Side Machine makes a replacement adjustable torque box, but I have never delt with this so I do not know if it works. I damaged my boxes very bad since I run the SSM which tend to be hard on the boxes, after welding the seams and adding the re-enforcement kit I have never had a single problem. I also welded plate across the bottom so it boxes the arm in a little. You just need to notch it out so that the arm still has room to travel. Wolfe sells similar plates for $25.00. ------------------ Check Out My Site 91GT,Holley SysteMAX II Kit-Heads 2.02" x 1.60" port matched to a 1262,Anderson N-61,30#,76mm C&L,75mm Accufab, Full MAC, No A/C or PS or emissions, 12" K&N Filter,RNH PERFORMANCE Ram Air,Ron Davis Radiator,Full Suspension, SPEC stage III clutch, Lakewood SFI bell, S&W 8pt "X" brace,JAZ seats,3:73's,Welds..etc,4:30's and 33 splines coming very soon! [b]12.16 @ 113.5, 1.78