Drag Suspension?

Rick 91GT · 10-30-2001, 09:11 AM

I run the SSM lift bars on mine, they work great with sticky tires on my combo. I run 70/30's, 50/50's and the Eibach Drag launch. You really should re-enforce the torque boxes no matter what arms you use they are weak from the factory. I sell my kit for $100 and they are stainless steel and will not rust, my design is a little different then "the others" and gives more support in my opinion.

If I was buying new I would strongly look at the UPR stuff, very nice stuff and it is similar to the Wolfe pieces. I am getting a pair of their double adjustable uppers with spherical busings,and the sway bar as well. www.uprproducts.com

What kind of numbers or results are you getting with your Holley kit?

------------------
Check Out My Site 91GT,Holley SysteMAX II Kit-Heads 2.02" x 1.60" port matched to a 1262,Anderson N-61,30#,76mm C&L,75mm Accufab, Full MAC, No A/C or PS or emissions, 12" K&N Filter,RNH PERFORMANCE Ram Air,Ron Davis Radiator,Full Suspension, SPEC stage III clutch, Lakewood SFI bell, S&W 8pt "X" brace,JAZ seats,3:73's,Welds..etc,4:30's and 33 splines coming very soon!
<B>12.16 @ 113.5, 1.78

[This message has been edited by Rick 91GT (edited 10-30-2001).]

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Drag Suspension Q's	Ieatcamaros	Windsor Power	19	03-21-2004 12:44 AM
Need Help, Budget Drag Suspension...	BowTie Eater 5 Liter	Windsor Power	6	07-24-2002 07:56 AM
info about drag suspension for a daily driver?	fastang	Windsor Power	9	11-25-2001 09:29 PM
Drag and Autox suspension?	1989GT	Corner Carvers Delight	7	12-15-1999 09:46 PM
drag suspension tech article is done, Check it out	11secondGT	Small Ponies	0	08-09-1999 07:06 PM

10-30-2001, 09:11 AM	#4
Rick 91GT Procharged! Join Date: May 1999 Location: Hanover, PA Posts: 1,539	I run the SSM lift bars on mine, they work great with sticky tires on my combo. I run 70/30's, 50/50's and the Eibach Drag launch. You really should re-enforce the torque boxes no matter what arms you use they are weak from the factory. I sell my kit for $100 and they are stainless steel and will not rust, my design is a little different then "the others" and gives more support in my opinion. If I was buying new I would strongly look at the UPR stuff, very nice stuff and it is similar to the Wolfe pieces. I am getting a pair of their double adjustable uppers with spherical busings,and the sway bar as well. www.uprproducts.com What kind of numbers or results are you getting with your Holley kit? ------------------ Check Out My Site 91GT,Holley SysteMAX II Kit-Heads 2.02" x 1.60" port matched to a 1262,Anderson N-61,30#,76mm C&L,75mm Accufab, Full MAC, No A/C or PS or emissions, 12" K&N Filter,RNH PERFORMANCE Ram Air,Ron Davis Radiator,Full Suspension, SPEC stage III clutch, Lakewood SFI bell, S&W 8pt "X" brace,JAZ seats,3:73's,Welds..etc,4:30's and 33 splines coming very soon! <B>12.16 @ 113.5, 1.78 [This message has been edited by Rick 91GT (edited 10-30-2001).]