Aluminum RRs good for only 20-30K miles??

PKRWUD · 11-02-2001, 10:04 AM

Pressure plays a very big role. Think about it... the closer you get to the center, the less movement there is, so it's not necessarily wear from routine use. However, under excessive load, the trunion would suffer stress whether it moved or not, but especially under heavy load, which most systems with a high lift cam and stiffer springs will routinely see. I can say that the rollers that I have replaced for customers or on the Sprint car were under alot of load. Keep in mind, though, that the real reason aluminum rollers were put to use was for racing, not for longevity. A race engine, and it's parts, rarely have to go for more than 500 miles, and sometimes as few as 1/4 mile. Also, you get what you pay for. No offense intended, but Sig Erson, for example, is K-mart quality. The ford rollers are actually top of the line Crane rollers that Crane customized for Ford. GM uses top quality rollers as well, but still lists them as a part to replace at 100k miles as routine maintenance. In my opinion, based on what I've seen, I wouldn't really recommend aluminum rollers for a daily driver. The difference between aluminum rollers and steel rollers isn't noticable in a mild street engine. But, steel rollers wear faster than sled-fulcrumed rockers too.

Take care,
-Chris

------------------
Retired Moderator
MustangNet

My site: Peckerwoods Pit Stop

My teams site: Jim Porter Racing

RACECAR spelled backwards is RACECAR

HEY !!! Are you ASE Certified ??? If you are, ask me about iATN.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Pretty Good weekend for me! Intimadated WS-6, Parts, Happiness.	Mercury	Blue Oval Lounge	15	02-06-2002 07:22 PM
Raced a Modded 94-95 GT. Good friends car.	Mercury	Stang Stories	14	12-16-2001 02:56 AM
Is this good?	Five0	Windsor Power	5	12-14-2001 06:37 PM
Got the 4.10's in tonight- good thing I did!!!	Killercanary	Windsor Power	3	03-31-2001 10:30 AM
Bosch O2 sensors, any good??	skiwesser	Windsor Power	5	03-30-2001 03:06 PM

11-02-2001, 10:04 AM	#1
PKRWUD Junior Member Join Date: Mar 1999 Location: Ventura, California Posts: 8,981	Pressure plays a very big role. Think about it... the closer you get to the center, the less movement there is, so it's not necessarily wear from routine use. However, under excessive load, the trunion would suffer stress whether it moved or not, but especially under heavy load, which most systems with a high lift cam and stiffer springs will routinely see. I can say that the rollers that I have replaced for customers or on the Sprint car were under alot of load. Keep in mind, though, that the real reason aluminum rollers were put to use was for racing, not for longevity. A race engine, and it's parts, rarely have to go for more than 500 miles, and sometimes as few as 1/4 mile. Also, you get what you pay for. No offense intended, but Sig Erson, for example, is K-mart quality. The ford rollers are actually top of the line Crane rollers that Crane customized for Ford. GM uses top quality rollers as well, but still lists them as a part to replace at 100k miles as routine maintenance. In my opinion, based on what I've seen, I wouldn't really recommend aluminum rollers for a daily driver. The difference between aluminum rollers and steel rollers isn't noticable in a mild street engine. But, steel rollers wear faster than sled-fulcrumed rockers too. Take care, -Chris ------------------ Retired Moderator MustangNet My site: Peckerwoods Pit Stop My teams site: Jim Porter Racing RACECAR spelled backwards is RACECAR HEY !!! Are you ASE Certified ??? If you are, ask me about iATN.