C&L 76mm

[DemonGT]

after i get my gears and shifter i might have enought money left for a cobra intake..and i was wondering if after i get that intake if i should get a C&L 73 or 76mm air meter..also should i go with a 65 or 70mm throttle body??i plan on a A-trim some time in the late future also..should i upgrade the fuel injectors before i get the air meter? and dose anyone that has the C&L 76 have a pic of what it looks like with that tube?

------------------
'91 GT,91K,T-5,air silencer removed,racing clutch(previous owner put in so dont know what kind),K&N air filter,Aiwa deck,power acoustic amp,2 12" pianeers,UPDATE: Just got my Mac long tube headers and Cat-back

Future Mods:3.73's,Pro 5.0,Shifter knob,FMS 9mm wires

[84_GT350]

Just an FYI...I've heard that C&L meter have problems with those sampling tubes. Something about part throttle/non-boosted drivability problems. I'm not trying to knock them...I don't own one. Just what I've heard. And this has been a while ago. Perhaps they've fixed the problem.

------------------
1984 1/2 GT350 (#842 Hatchback w/ T-tops), 302HO, Comp cams Xtreme Energy cam, Carter 625cfm carb, Weiand Stealth intake, MSD distributor, MSD coil, FMS 9mm wires, 1 5/8" MAC unequal shorties, 2 1/2" MAC Prochamber H-pipe, Flowmaster 2 chambers, KYBs, 16"x8" 4 lug Cobra Rs, Falken 245/45ZR16s

[gt93mustang]

I have had my 73mm for almost two years now and it has been great for me. I went from 19lb injectors, 24lber, to 30lbs changing the sample tube for each and it still ran great. I ordered the 76mm last Wednesday and thought it would get here today, but I didn't see it. I am hoping it gets here tomorrow. I will let you know how it works out.

------------------
MAC equal length headers, MAC Off-Road H-Pipe, Flowmaster mufflers, 373's, March ram-air kit, underdrive pulleys, 73mm MAF, 75mm TB, Saleen Intake (ported), Edelbrock 6037 heads (ported, polished, 3 angle valve-job 255CFM @.500), 1.6 FMS RR's, Wolverine 1087 Cam, 24lb injectors, MSD 6AL, Subframe connectors, Griggs Adustable Lower Control Arms, Lakewood 50/50 shocks, SSM Upper Control Arms... and probably some more in there I forgot

[Rick 91GT]

I have heard C&L has fixed there issues. I just got rid of my 75mm Pro-M and got the 76mm C&L kit with discharge tube, but like 93GT it isn't here yet.
www.cnlperformance.com they have a good article on it, good pictures also.

------------------
My Ride Check Out My Site 91GT, Holley SysteMAX II Kit-Heads 2.02" x 1.60",Full MAC exhaust 1-5/8" Long tubes, 2-1/2" O.R H-Pipe, 2 1/2" cat back, 12" K&N Filter, RNH PERFORMANCE Ram Air, Ron Davis Radiator, Full Suspension,3:73's, Welds, Best on new motor-12.60 @ 108, no traction 1.98

[DemonGT]

gt93 how do yo recalibrate it with out sending it back?

------------------
'91 GT,91K,T-5,air silencer removed,racing clutch(previous owner put in so dont know what kind),K&N air filter,Aiwa deck,power acoustic amp,2 12" pianeers,UPDATE: Just got my Mac long tube headers and Cat-back

Future Mods:3.73's,Pro 5.0,Shifter knob,FMS 9mm wires

[gt93mustang]

Demon, it comes with a tube that can be removed and swapped when going with larger injectors. When you upgrade (or downgrade for that matter) all you do is change the sample tube and it is 'recalibrated'. It is much easier then sending it back to the company and paying for shipping there, paying to have them recalibrate it, and paying to have it shipped back... That's why I will be sticking with C&L for a while.

------------------
MAC equal length headers, MAC Off-Road H-Pipe, Flowmaster mufflers, 373's, March ram-air kit, underdrive pulleys, 73mm MAF, 75mm TB, Saleen Intake (ported), Edelbrock 6037 heads (ported, polished, 3 angle valve-job 255CFM @.500), 1.6 FMS RR's, Wolverine 1087 Cam, 24lb injectors, MSD 6AL, Subframe connectors, Griggs Adustable Lower Control Arms, Lakewood 50/50 shocks, SSM Upper Control Arms... and probably some more in there I forgot

[DemonGT]

93gt did you have to pay extra for the samplaling tubes or did it come with your 73mm?

------------------
'91 GT,91K,T-5,air silencer removed,racing clutch(previous owner put in so dont know what kind),K&N air filter,Aiwa deck,power acoustic amp,2 12" pianeers,UPDATE: Just got my Mac long tube headers and Cat-back

Future Mods:3.73's,Pro 5.0,Shifter knob,FMS 9mm wires

[2FastLX]

As opposed to the Pro-M meters costing an arm and a leg and a big toe to have recalibrated the C&L meters only cost $40 (for a new sampling tube). And you could probably find someone to buy your old tube should you ever decide to switch injector size. I would at least buy 24lb injectors when you buy the meter because you'd probably be able to sell a 24lb tube a lot easier then you could a tube for stock injectors.

I just got my 76mm, but mine was some kind of pre-production unit and was machined as a 76mm, but was still machined on the outside as a 73mm so it didn't come with the power pipe. I went ahead and got this from the guy because I wanted to use the MAC cold air kit with it, plus I have a meter that very few people have

The quality of this meter is 10 times better than that of the plastic Pro-M meters and is very polishable. I think I'm gonna love mine after I get the cold air kit installed and get my new meter polished.

------------------
Indiana Stangers Association
Buy your parts here

[gt93mustang]

Demon, I got mine used, but when you initially buy it, it comes with a sample tube for the calibration of your choice. Each time you change injectors, you have to get a new tube, which usually costs about $30.00, or you can probably find one from someone with a used one for $10-$15 bucks.

-As a side note, I am looking to get rid of my 73mm C&L. I have both 19 and 24lb sample tubes. I don't know what they are going for nowadays, so I am taking offers. It is in the beginning stages of being polished and looks much better than the rough cast that comes from C&L. If anyone is interested, please send me an email and we can work something out.

[Oldwantabe]

Originally Posted by gt93mustang

Demon, I got mine used, but when you initially buy it, it comes with a sample tube for the calibration of your choice. Each time you change injectors, you have to get a new tube, which usually costs about $30.00, or you can probably find one from someone with a used one for $10-$15 bucks.

-As a side note, I am looking to get rid of my 73mm C&L. I have both 19 and 24lb sample tubes. I don't know what they are going for nowadays, so I am taking offers. It is in the beginning stages of being polished and looks much better than the rough cast that comes from C&L. If anyone is interested, please send me an email and we can work something out.

I need a 24 lb. tube. 478 935 9086 before 9 pm.Off the week of Thanksgiving
Thanks
Darrell

[USMC302]

Oldwantabe, This thread is from 2001, most likely he won't have that avail anymore. You might want to try searching Ebay or get one from C&L directly. Good luck.

[Oldwantabe]

Originally Posted by USMC302

Oldwantabe, This thread is from 2001, most likely he won't have that avail anymore. You might want to try searching Ebay or get one from C&L directly. Good luck.

Thanks. I saw the thread and didn't pay attention to the date.I was just trying to find one cheap,you know how us older folks are.It does ok with the stock one.I just need to open it up a little more.It turns 100.89 14.238 peddling 1st gear already.I want to put the 73 mm and I have a pro 5 0 .I need also a couple of stickier rear tires.Thanks again.