

© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
![]() |
#1 |
Registered Member
Join Date: May 1999
Location: sloatsburg
Posts: 261
|
![]() okay here is the problem i want to run a 150 shot but all the techs at nos say i need to put an inline pump in that will boost the pressure right now im running 135 with a 190 intake is anybody running a 150 with just the intake pump i also have a 255 that i was pplaning on putting in any help would be very apriciated im going to the track sat and kinda need some imput thanks
__________________
306 edelbrock 6037 heads full mac exuast 1.7 rr 373 rear hd clutch tremec mighty demon 650 carb msd ignition rpm air gap intake custom cam still trying to get it to run right |
![]() |
![]() |
![]() |
#2 |
I'd rather be basketweaving
Join Date: Feb 2000
Location: Indianapolis
Posts: 2,551
|
![]() i'd put the 255 in if i were you
__________________
NMRA O/C 9516 NA pumpgas stickshift 347 10.65@125.6, 6.73@100, 1.41 60ft |
![]() |
![]() |
![]() |
#3 |
Registered Member
Join Date: Mar 1999
Location: Largo, FL USA
Posts: 274
|
![]() I agree with fiveohpatrol. That's a lot of juice and if you go lean you are screwed. Do you have a progressive controller for the NO? If not how is that as far as the shock on the tires?
__________________
Negative Mustang @ present time. |
![]() |
![]() |
![]() |
#4 |
Registered Member
Join Date: May 2001
Location: Valdese, NC
Posts: 361
|
![]() The 190 would be enough if you were still stock, but with the addition of heads on your setup, your going to be pushing the 190. Better go with the 255 for safety, unless you just like changing headgaskets
![]()
__________________
91 single turbo vert |
![]() |
![]() |
![]() |
#5 |
Registered Member
Join Date: May 1999
Location: sloatsburg
Posts: 261
|
![]() SO YOU THINK I SHOULD BE FINE WITH THE 255 PUMP
__________________
306 edelbrock 6037 heads full mac exuast 1.7 rr 373 rear hd clutch tremec mighty demon 650 carb msd ignition rpm air gap intake custom cam still trying to get it to run right |
![]() |
![]() |
![]() |
#6 |
Registered Member
Join Date: Feb 1999
Location: Utica, Michigan
Posts: 2,631
|
![]() I run a 255 itank with no other additional pump.
__________________
1988 Mustang GT stock bottom 302, C4 10.9 @ 128 with 8 psi of Novi 1000 boost!----STOLEN 1989 Mustang notchback Warmed up 306 with a Procharger. |
![]() |
![]() |
![]() |
#7 |
Registered Member
Join Date: May 1999
Location: sloatsburg
Posts: 261
|
![]() how much of a shot are you running with the 255
__________________
306 edelbrock 6037 heads full mac exuast 1.7 rr 373 rear hd clutch tremec mighty demon 650 carb msd ignition rpm air gap intake custom cam still trying to get it to run right |
![]() |
![]() |
![]() |
#8 |
Registered Member
Join Date: Nov 2001
Location: Sunny, Hot, Sebring, Florida
Posts: 725
|
![]() The tech's at NOS are right on, the in-tank pump will not provide the overall volume you need, yes, people get by with just the in-tank, but it is a gamble, do you want to gamble on your motor, an in-line pump is much cheaper than holed pistons.
__________________
Remember...2nd place is 1st place for losers! |
![]() |
![]() |
![]() |
#9 |
Registered Member
Join Date: Feb 1999
Location: Utica, Michigan
Posts: 2,631
|
![]() My fuel pressure stays a tad above 80 psi all the way down the track, but yes if I found a deal on a booster pump I would put it on. It can't hurt and is good insurance.
|
![]() |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
which nitrous system is for me? | LXStallion | Windsor Power | 1 | 02-17-2002 01:55 AM |
PLEASE HELP!! Do I need the smog pump system to pass dyno emissions ?? | Stang_ROTY | Windsor Power | 5 | 07-02-2001 01:09 AM |
Serpentine or V-belt system for a early 351 | Stang_ROTY | Windsor Power | 4 | 06-20-2001 05:02 PM |
Cartech/Aeromotive fuel system owners please read!!!! | Black306 | Windsor Power | 4 | 06-18-2001 03:39 PM |
R2000 cleaning system for engine??? | fongo | Windsor Power | 1 | 01-04-2001 06:21 PM |