pissed off about gears

gray87GT · 04-03-2001, 11:46 PM

After worked I stopped off at two tranny places. First said he would install gears for $1000+, second said I would need a new carrier so it would be about the same. Are these guys full of sh*t? Do you guys think it's worth it to buy a used rear end with the gears in there already, how many miles is too many??? How about rear discs.....if I got a used rear end I might as well get it with discs...so all I would need is a new master and proportioning valve right?? Any help is great cause I am stuck. Thanks

------------------
87 GT, BBK shorty's, offroad H-pipe, ASP pullies, 70mm T.B., Cobra intake, no smog pump, Windsor Jr irons, Comp cams 1.6 rollers, F303 cam, H.D. export W.P., Tri-Ax, FMS subframes, Battle boxes, SSM liftbars, FMS King Cobra clutch, mass-air conversion, 73mm C&L, 24lb injectors, BBK fuel pressure regulator, 3/8" no EGR spacer, and other piddly sh*t.

Skyman · 04-04-2001, 01:07 AM

Thats a rip!!! My rear end has 151k miles on it, still going strong and hittin 12's now.

------------------
-1989 Saleen Mustang #406- TFS Heads, E-303, edelbrock intake,70MM TB, 73mm MAF, off road H, headers and 3chamber flows.
12.55@107mph
Runs on 87 Octane and gets 24mpg!

Doctor DeBo · 04-04-2001, 01:16 AM

Skyman is right,that is a rip.I would let Helen Keller put my rear end together before I would pay $1000.I did mine myself(not easy),Im almost willing to bet a good local Ford dealer would do it for much less.As far as the used rear end be carfull,unless you know who your getting it from.

Dark Knight · 04-04-2001, 11:49 AM

you can buy a complete 8.8 minus axles for around $600 from ford with your gear choice..

------------------
84 convt,'95 302,AFR's, performer
3.55's, underdrives stock shorties
stock cam, 1.7's
14.06@100.21, 255RWHP on a hot day
265 on the mph/weight chart

Rick 91GT · 04-04-2001, 04:06 PM

A gear install including gears should be around $400.00. Make sure you get new bearings, if your car has a good amount of miles it is better safe then sorry. If you are willing to spend $1000, get a new carrier and upgrade to 31 splined axles.

------------------
Check Out My Site 91GT,Holley SysteMAX II Kit-Heads 2.02" x 1.60" port matched to a 1262,Anderson N-61,24#,76mm C&L,Full MAC exhaust 1-5/8" Long tubes,2-1/2" O.R H-Pipe,2 1/2" cat back, No A/C or PS or emissions, 12" K&N Filter,RNH PERFORMANCE Ram Air,Ron Davis Radiator,Full Suspension,S&W 8pt "X" brace,JAZ seats,3:73's,Welds..etc,4:30's and 31 splines coming very soon!

Cliff92Z · 04-04-2001, 08:25 PM

That shop is chraging you $1000+ just to install gears? I don't think so. I went to the Chevy dealer and they only charged me $280 (labor) to install new gears AND a new differential. I would keep looking around, try your local Ford dealer. Aside from the gears, you may save some money if you buy a kit with new bearings, shims, sleeves, gaskets...all that good stuff. I'd imagine the dealer would charge a bunch for those additional parts. And its probably not a bad idea to replace those internals. I did. Good luck.

------------------
1992 Z28 TPI.
160' stat, Accel 8mm, Accel Cap & Rotor,
Flowmaster, high-flo cat.
700R4 3.73s HD Zexel Torsen

gray87GT · 04-04-2001, 09:01 PM

Gear update:

I was talking to a machinist who does CNC work for me and he mentioned he knows a guy who used to work at a Ford Dealership, he said he installs gears on the side. I called him up and he said he'd do it for $125 labor plus parts, I just have to buy the gears and he'll get the rest for me!! He was the Mustang "expert" at the Dealership. I can't wait.

04-03-2001, 11:46 PM	#1
gray87GT Registered Member Join Date: Jan 2001 Location: Minnesota Posts: 177	pissed off about gears After worked I stopped off at two tranny places. First said he would install gears for $1000+, second said I would need a new carrier so it would be about the same. Are these guys full of sht? Do you guys think it's worth it to buy a used rear end with the gears in there already, how many miles is too many??? How about rear discs.....if I got a used rear end I might as well get it with discs...so all I would need is a new master and proportioning valve right?? Any help is great cause I am stuck. Thanks ------------------ 87 GT, BBK shorty's, offroad H-pipe, ASP pullies, 70mm T.B., Cobra intake, no smog pump, Windsor Jr irons, Comp cams 1.6 rollers, F303 cam, H.D. export W.P., Tri-Ax, FMS subframes, Battle boxes, SSM liftbars, FMS King Cobra clutch, mass-air conversion, 73mm C&L, 24lb injectors, BBK fuel pressure regulator, 3/8" no EGR spacer, and other piddly sht.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Gears Gears Gears!!!!	COBRAon18s	Modular Madness	20	05-13-2002 04:44 PM
how can you tell what size gears you have?	Kamaro Killer	Windsor Power	7	04-03-2002 02:55 PM
Gears, need help!!!!	Edgar Negron	Windsor Power	3	05-27-2001 03:10 PM
Gears Gears Gears	Skyman	Windsor Power	6	03-11-2001 11:39 PM
Attn: My Mustang brothers and sisters. Getting gears.	Fox Body	Blue Oval Lounge	9	02-16-2001 12:36 PM

04-04-2001, 01:07 AM	#2
Skyman I need 110mph Trap Speed! Join Date: Feb 1999 Location: So, CA Posts: 4,315	Thats a rip!!! My rear end has 151k miles on it, still going strong and hittin 12's now. ------------------ -1989 Saleen Mustang #406- TFS Heads, E-303, edelbrock intake,70MM TB, 73mm MAF, off road H, headers and 3chamber flows. 12.55@107mph Runs on 87 Octane and gets 24mpg!

04-04-2001, 01:16 AM	#3
Doctor DeBo Registered Member Join Date: Feb 2000 Location: Newnan, GA, UnitedStates Posts: 83	Skyman is right,that is a rip.I would let Helen Keller put my rear end together before I would pay $1000.I did mine myself(not easy),Im almost willing to bet a good local Ford dealer would do it for much less.As far as the used rear end be carfull,unless you know who your getting it from.

04-04-2001, 11:49 AM	#4
Dark Knight Registered Member Join Date: Oct 1998 Location: Az Posts: 854	you can buy a complete 8.8 minus axles for around $600 from ford with your gear choice.. ------------------ 84 convt,'95 302,AFR's, performer 3.55's, underdrives stock shorties stock cam, 1.7's 14.06@100.21, 255RWHP on a hot day 265 on the mph/weight chart

04-04-2001, 04:06 PM	#5
Rick 91GT Procharged! Join Date: May 1999 Location: Hanover, PA Posts: 1,539	A gear install including gears should be around $400.00. Make sure you get new bearings, if your car has a good amount of miles it is better safe then sorry. If you are willing to spend $1000, get a new carrier and upgrade to 31 splined axles. ------------------ Check Out My Site 91GT,Holley SysteMAX II Kit-Heads 2.02" x 1.60" port matched to a 1262,Anderson N-61,24#,76mm C&L,Full MAC exhaust 1-5/8" Long tubes,2-1/2" O.R H-Pipe,2 1/2" cat back, No A/C or PS or emissions, 12" K&N Filter,RNH PERFORMANCE Ram Air,Ron Davis Radiator,Full Suspension,S&W 8pt "X" brace,JAZ seats,3:73's,Welds..etc,4:30's and 31 splines coming very soon!

04-04-2001, 08:25 PM	#6
Cliff92Z Registered Member Join Date: Mar 2001 Location: Atlanta, GA Posts: 13	That shop is chraging you $1000+ just to install gears? I don't think so. I went to the Chevy dealer and they only charged me $280 (labor) to install new gears AND a new differential. I would keep looking around, try your local Ford dealer. Aside from the gears, you may save some money if you buy a kit with new bearings, shims, sleeves, gaskets...all that good stuff. I'd imagine the dealer would charge a bunch for those additional parts. And its probably not a bad idea to replace those internals. I did. Good luck. ------------------ 1992 Z28 TPI. 160' stat, Accel 8mm, Accel Cap & Rotor, Flowmaster, high-flo cat. 700R4 3.73s HD Zexel Torsen

04-04-2001, 09:01 PM	#7
gray87GT Registered Member Join Date: Jan 2001 Location: Minnesota Posts: 177	Gear update: I was talking to a machinist who does CNC work for me and he mentioned he knows a guy who used to work at a Ford Dealership, he said he installs gears on the side. I called him up and he said he'd do it for $125 labor plus parts, I just have to buy the gears and he'll get the rest for me!! He was the Mustang "expert" at the Dealership. I can't wait.