NE1 have vibration problems with Centerforce clutch

over 40 five oh driver · 01-17-2001, 02:13 AM

Hey guy...I'm right up the road from you in Spring, Texas. Did you install the CF yourself? If so, did you index the driveshaft for reinstallation? It doesn't take much to get an imbalamce...Not getting the bellhousing torqued properly to the block...worn pilot bearing...tranny not torqued to the bellhousing properly...pressure plate not seated evenly onto the flywheel...flywheel, or bellhousing runout out of tolerance...driveshaft not indexed properly...tranny mount bad or not torqued...internal tranny problem. Mine had a vibration across the entire RPM range and I pulled it all back apart and found the pressure plate was not fully seated around the entire circumference of the flywheel due to incorrect pressure plate bolts I'd got from Summit. Anyways...hard to pinpoint it for ya, but just be methodical and I am sure you can get it narrowed down. Sounds like a nice ride you got there...maybe we'll see each other at Fun Ford/Houston Raceway Park. Good luck...Dave

------------------
*92' GT, Keith Craft Racing 306 (10.25:1 CR), PRO-M 80mm MAF,65MM TB, Edelbrock U/L intake,
TFS-TW heads milled .056" (52cc chambers), CompCams XE274HR (.555/.565" lift w/1.6 rockers), A-351 adjustable roller rockers, 30# injectors,
Kirban FPR w/external pump, FRPP ceramic coated headers, Bassani X-pipe w/cats, Bassani cat back, Centerforce DF clutch/T.O. bearing...MSD 6AL w/MSD distributor, Steeda Tri axe, aluminum D/S, 3.73's, w/Factory Five U/L control arms. Lakewood 50/50 shocks. Stee

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
centerforce clutch problems	Z28EATR	Windsor Power	6	02-18-2004 05:59 PM
'65 - Pull Away Problems - Action Plan	geordie	Classic Mustangs	0	05-14-2002 01:43 PM
'65 Mustang - Pull Away Problems	geordie	Classic Mustangs	6	05-11-2002 04:46 PM
Clutch Problems	blue302	Windsor Power	3	09-10-2001 01:37 PM
billed 5 times to install clutch by Pauls Auto, please read and give opinions (long)	beefcake	Blue Oval Lounge	2	02-23-2001 03:05 PM

01-17-2001, 02:13 AM	#2
over 40 five oh driver Registered Member Join Date: Sep 1998 Location: Oklahoma City Posts: 278	Hey guy...I'm right up the road from you in Spring, Texas. Did you install the CF yourself? If so, did you index the driveshaft for reinstallation? It doesn't take much to get an imbalamce...Not getting the bellhousing torqued properly to the block...worn pilot bearing...tranny not torqued to the bellhousing properly...pressure plate not seated evenly onto the flywheel...flywheel, or bellhousing runout out of tolerance...driveshaft not indexed properly...tranny mount bad or not torqued...internal tranny problem. Mine had a vibration across the entire RPM range and I pulled it all back apart and found the pressure plate was not fully seated around the entire circumference of the flywheel due to incorrect pressure plate bolts I'd got from Summit. Anyways...hard to pinpoint it for ya, but just be methodical and I am sure you can get it narrowed down. Sounds like a nice ride you got there...maybe we'll see each other at Fun Ford/Houston Raceway Park. Good luck...Dave ------------------ *92' GT, Keith Craft Racing 306 (10.25:1 CR), PRO-M 80mm MAF,65MM TB, Edelbrock U/L intake, TFS-TW heads milled .056" (52cc chambers), CompCams XE274HR (.555/.565" lift w/1.6 rockers), A-351 adjustable roller rockers, 30# injectors, Kirban FPR w/external pump, FRPP ceramic coated headers, Bassani X-pipe w/cats, Bassani cat back, Centerforce DF clutch/T.O. bearing...MSD 6AL w/MSD distributor, Steeda Tri axe, aluminum D/S, 3.73's, w/Factory Five U/L control arms. Lakewood 50/50 shocks. Stee